4K60 Fiber Optic Output Card for Flex Matrix Pro
KanexPro FLEX-PROFIB-OUT for Flex Matrix Pro. Fiber Optic (LC). 4K60, Dante/AES67, TAA.
Add four Fiber Optic (LC) outputs to any Flex Matrix Pro chassis. The FLEX-PROFIB-OUT delivers 4K60 4:4:4 at 18Gbps with HDCP 2.2, HDR, scaling, and Dante/AES67 per port. Seamless switching. EDID/HDCP management. Hot-swappable. TAA compliant. Singlemode 2km. Multimode 300m.
- 4× Fiber Optic (LC) outputs — hot-swappable across all Flex Pro chassis (16×16 to 128×128)
- 4K60 4:4:4 at 18Gbps • HDCP 2.2 • HDR
- Dante/AES67 network audio • 8ch LPCM High-Res Audio
- Independent scaling per output • seamless switching • EDID/HDCP management
- Singlemode 6,562ft (2km) • Multimode 984ft (300m) • adaptive SM/MM
- Hot-swappable • TAA compliant
Specifications| Card ports | 4 X 1 LC Fiber Output Port |
|---|
| Connector Type | LC |
|---|
| Signal Type | Fiber w/ Adaptive Single Mode & Multimode Processing |
|---|
| Optical Loss Budget: | Single Mode 9 dB, Multimode 8 dB |
|---|
| Maximum Receiver Sensitivity | Single mode -15dbm, Multi-mode -16dbm |
|---|
| Video Resolution: | Up to 3840x2160 60Hz 4:4:4 (8bit) |
|---|
| Operating Distance: | Single-mode 1.24 Mile (2 KM), Multi-mode 984 mile (300 m) |
|---|
| Normal Peak Wavelength | 1550nm, 1310nm |
|---|
| Analog Audio Port | 4 X 3-pin Phoenix stereo audio for Extraction |
|---|
Questions
- How many fiber outputs does the FLEX-PROFIB-OUT provide and what connector does it use?
- The card provides 4 fiber optic output ports using LC connectors, each with adaptive single mode and multimode processing.
- What resolution and bandwidth does the FLEX-PROFIB-OUT support?
- Each output supports video resolutions up to 3840x2160 @60Hz 4:4:4 (8-bit), with HDMI 2.0 and HDCP 2.2 compliance and HDR support.
- Which receiver connects to the FLEX-PROFIB-OUT card?
- The FLEX-PROFIB-RX (fiber optic to HDMI receiver) connects directly to the FLEX-PROFIB-OUT card, receiving video with embedded audio and bidirectional RS-232 up to 6,562 ft (2KM) over single fiber optic cable.
- Which Flex Pro chassis models accept the FLEX-PROFIB-OUT card?
- It is hot-swappable across all Flex Pro main frame models: FLEX-PRO16X16, FLEX-PRO32X32, FLEX-PRO64X64, and FLEX-PRO128X128.
- Does the FLEX-PROFIB-OUT card require its own power adapter?
- No local power adapter is documented for the card itself; it is powered by the Flex Pro chassis.
- Can the FLEX-PROFIB-OUT be installed or removed without powering down the chassis?
- Yes. The card is hot-swappable, so it can be installed or replaced in a Flex Pro chassis card slot without taking the matrix offline.
- There is no signal at a display connected through a FLEX-PROFIB-OUT output. What should I check?
- Confirm a FLEX-PROFIB-RX is connected at the far end and powered, verify the fiber type (single mode or multimode) is within its rated distance, and check that the fiber connectors are clean and fully seated.
- The Flex Pro chassis does not recognize an installed FLEX-PROFIB-OUT card. What should I do?
- Remove and reseat the card in its slot to trigger hot plug and auto detect; if it is still not recognized, try a different card slot in the chassis.
- Why choose the FLEX-PROFIB-OUT over the FLEX-PROCAT-OUT card?
- The FLEX-PROFIB-OUT reaches up to 6,562 ft (2KM) over singlemode fiber, far beyond the FLEX-PROCAT-OUT's 330 ft (100M) CAT6A limit, making it suited to long-distance or inter-building runs.
- What installation scenario is the FLEX-PROFIB-OUT best suited for?
- It suits projects distributing 4K signal over long distances to displays located in another building or across a large facility, using fiber runs beyond the practical range of copper CAT cabling.