8-Button Programmable IP Wall Plate Keypad with PoE
KanexPro WP-IPKEYPAD8 is an 8-button PoE-powered IP wall plate keypad for AV macro control. 128-command capacity, relay output, time-based scheduling…
The KanexPro WP-IPKEYPAD8 is a programmable 8-button IP control keypad that fits a standard US single-gang wall plate and requires no dedicated control processor. Each of the 8 backlit buttons can trigger a fully customized macro, sending TCP/IP commands to any Ethernet-connected AV device on the network — projectors, matrix switchers, displays, relay-controlled screens, and more. With up to 128 total commands storable across all macros (up to 16 per macro) and an additional 8 software-only extension macros accessible via WebGUI, the WP-IPKEYPAD8 delivers enterprise-grade macro control at a fraction of the cost of a full control system. Powered over Ethernet (PoE 48V PD) or via the included 5V/2.6A DC adapter, the keypad installs cleanly without a dedicated power run. The integrated clock and calendar-based scheduling engine enables time-triggered and recurring macro execution — ideal for automated display power-on/off, screen raise/lower via relay, and room mode switching on a daily or weekly schedule. Dual-color LEDs (red and blue) per button provide visual state feedback with individually adjustable brightness. Programming is handled entirely through the built-in WebGUI, Telnet, or the physical buttons — no proprietary software license required.
- US single-gang wall plate design with adjustable LED brightness
- 8 physical macro buttons — each configurable to execute multiple commands via WebGUI
- Up to 128 total commands storable across all macros (up to 16 commands per macro)
- 8 additional software-only extension macros accessible via WebGUI or Telnet
- Relay output (DC 0–24V / 5A) — open, close, or toggle for screen and device control
- Time and date macro scheduling — up to 32 recurring + 8 one-time events
- 48-hour battery backup for internal clock — protects scheduled events against power loss
- Customizable daylight saving time settings for scheduling accuracy
- Toggle mode — alternate between two macro sets on successive button presses
- Repeat mode — macro repeats continuously while button is held
Specifications| Specification | Value |
|---|
| Input Ports | 8× Backlit Buttons, 1× IP Control (RJ45) |
|---|
| Output Port | 1× Relay (2-pin Terminal Block, DC 0–24V / 5A) |
|---|
| Config Port | 1× Mini USB (behind wall plate) |
|---|
| PoE | 48V PD (requires PoE PSE switch/hub) |
|---|
| DC Power | 5V/2.6A DC adapter included (CE/FCC/UL) |
|---|
| Power Consumption | 3.3W |
|---|
| Protocols | TCP/IP, Telnet, WebGUI |
|---|
| Macro Capacity | 16 physical + 8 extension (WebGUI only) |
|---|
| Command Capacity | 128 total (up to 16 per macro) |
|---|
| Scheduling | 32 recurring + 8 one-time events |
|---|
| Clock Backup | 48-hour battery-backed |
|---|
| Dimensions (W×H×D) | 2.75? × 4.50? × 1.49? (69.9 × 114.3 × 38mm) All Inclusive |
|---|
| Net Weight | 0.33 lbs (150g) |
|---|
| Form Factor | US single-gang wall plate |
|---|
| Chassis Material | Plastic, Metal |
|---|
| Color | White |
|---|
| Operating Temp | 32°F – 104°F (0°C – 40°C) |
|---|
| Storage Temp | -4°F – 140°F (-20°C – 60°C) |
|---|
| Humidity | 20–90% RH (non-condensing) |
|---|
| Certifications | CE, FCC, UL |
|---|
| ESD Protection | ±12kV air discharge / ±8kV contact discharge |
|---|
| 1× | IP Control Keypad (US single-gang) |
|---|
| 1× | USB Type-A to Mini-B cable |
|---|
| 1× | Terminal block connector |
|---|
| 2× | Button sticker sheets |
|---|
| 1× | 5V/2.6A DC power adapter |
|---|
| 1× | Operation manual |
|---|
Questions
- Does the keypad require an active internet connection?
- No. All control operates over the local LAN only. An active Ethernet connection to a switch or router is required to reach other IP devices on the same network, but no internet or cloud service is used.
- What happens to scheduled events during a power outage?
- The internal clock is battery-backed for 48 hours. Scheduled events remain intact and resume when power is restored within that window.
- Can it control RS-232 or IR devices?
- Not natively. The WP-IPKEYPAD8 sends TCP/IP (Telnet) commands and relay triggers only. For RS-232 or IR device control, pair with a network-connected RS-232/IR gateway on the same LAN.
- Can multiple keypads be used in the same installation?
- Yes. Each keypad is independently configured with its own IP address and can control overlapping or distinct device sets. There is no per-system limit on keypad count.
- Is PoE required, or can I use the included power adapter?
- Either works. The included 5V/2.6A DC adapter powers the unit fully when a PoE switch is not available. PoE (48V PD) is optional but eliminates the need for a power outlet near the wall plate.
- How are the buttons programmed?
- Through the built-in WebGUI accessed via any browser on the same network. No proprietary software, license, or app is required. Telnet commands can also be used for scripted setup.
- No response from devices after programming macros?
- Verify all devices are on the same LAN subnet as the keypad. Check that the destination IP and port are correct in Command Settings. Ensure a minimum 500ms delay between Telnet commands.
- What is the default IP address?
- 192.168.1.50. Use the included Device Discovery Tool or Telnet IPCONFIG command to locate or change the IP address.