Dante Powered 2-Channel Line In Audio Input Encoder with POE
KanexPro AUD-DTE-ECODE converts 2-channel balanced/unbalanced analog audio to Dante® via 6-pin Phoenix input, with 3-level gain and PoE or DC 12V power.
Puts two channels of balanced or unbalanced analog audio onto the Dante network from screw-terminal Phoenix wiring, powered by PoE or DC 12V. A 3-level gain switch (+18dBu, 0dBu, -10dBv) matches the source, and its compact metal enclosure is the companion form factor to the AUD-DTE-DCODE decoder. Pair it with KanexPro Dante amplifiers and wall plates, and plan it in the KanexPro System Planner with the rest of the room (one drawing and parts list). The KanexPro AUD-DTE-ECODE is a Dante®-enabled 2-channel analog audio encoder built on the Dante Ultimo solution. It accepts balanced or unbalanced analog audio via a 6-pin Phoenix connector and encodes it as Dante® 2CH digital audio for transmission over a standard Ethernet network. A 3-level GAIN switch (+18dBu, 0dBu default, -10dBv) matches input sensitivity to the connected source. Powered by PoE or DC 12V, it is designed for permanent installation in commercial AV environments where screw-terminal Phoenix wiring is standard practice.
- Converts 2-channel balanced/unbalanced analog audio to Dante® 2CH digital audio via 6-pin Phoenix connector
- 3-level input gain adjustment: +18dBu, 0dBu (default), -10dBv via GAIN dip switch
- Dante® audio sampling: 44.1kHz, 48kHz, 96kHz @ 24-bit; AES67 RTP compatible
- Configurable Dante® device latency via Dante® Controller software
- Installation-grade Phoenix connector input — screw-terminal field wiring, no pigtails
- Dual power: PoE IEEE 802.3af Class 0 or DC 12V via 2-pin Phoenix connector
- Metal enclosure, compact 120×47×26mm — companion form factor to AUD-DTE-DCODE
- Plan it in the KanexPro System Planner with the rest of the room: one drawing and parts list
Specifications| Input | 1× 6-pin Phoenix 3.81mm (CH1+/-/GND, CH2+/-/GND) balanced/unbalanced analog |
|---|
| Output | 1× Dante® RJ45 (PoE), PCM 2CH 44.1/48/96kHz @ 24-bit |
|---|
| Input Gain | +18dBu / 0dBu (default) / -10dBv (3-position GAIN switch) |
|---|
| Power Input | 1× 2-pin Phoenix 3.81mm (DC 12V) |
|---|
| Network | 100Mbps | Up to 100m (CAT6/CAT6A) |
|---|
| Control | Dante® Controller | AES67 RTP compatible |
|---|
| Power | PoE IEEE 802.3af Class 0 | DC 12V (2-pin Phoenix) | 1.2W max |
|---|
| Dimensions | 120 × 47 × 26mm | 186g | Metal, Black |
|---|
| Weight | 0.41 lbs |
|---|
| Temperature | Operating: 0°C–40°C | Storage: -20°C–60°C | 20–90% RH |
|---|
Questions
- How does the AUD-DTE-ECODE fit into a mixer-to-network signal chain?
- The 6-pin Phoenix input accepts the analog output of a mixer console or line source, and the unit encodes it to Dante 2CH PCM for delivery over the DANTE (PoE) RJ45 port to any Dante-enabled amplifier or DSP on the network.
- Why choose the AUD-DTE-ECODE for legacy analog sources on a Dante network?
- Its 6-pin Phoenix screw-terminal input and 3-level gain switch are built for installation-grade field wiring, letting integrators put existing mixers, BGM sources, or line-level processors onto a Dante network without pigtail adapters.
- There is no Dante link from the encoder - what should I check?
- Confirm the DANTE (PoE) RJ45 port is connected to a PoE-capable switch with a CAT6 or CAT6A straight-through cable (not cross-connected) and check that the green LINK LED is solid on; the yellow DATA LED should flash during active transmission.
- How is the AUD-DTE-ECODE powered?
- It accepts PoE IEEE 802.3af Class 0 through the DANTE RJ45 port, or DC 12V through the included 2-pin Phoenix connector when PoE is unavailable; maximum power consumption is 1.2W.
- What analog input levels does the unit accept?
- Balanced/unbalanced analog input is selectable via a 3-position GAIN switch: +18dBu, 0dBu (default), or -10dBv.
- What Dante audio format does the AUD-DTE-ECODE output?
- It outputs Dante 2CH PCM audio at 44.1kHz, 48kHz, or 96kHz, 24-bit, and is AES67 RTP compatible.
- How do I set the input gain to match my source?
- Set the 3-position GAIN dip switch: position 1 for +18dBu on high-headroom professional outputs, position 2 (default) for 0dBu standard line-level sources, or position 3 for -10dBv on consumer-level sources; activate only one position at a time.
- How do I wire the analog input?
- Use the included 6-pin Phoenix (IN) male connector (3.81mm pitch), pin order CH1+ / CH1- / GND / CH2+ / CH2- / GND, for balanced or unbalanced field wiring from a mixer, DSP, or line source.
- The encoded signal is clipping or too quiet at the receiving Dante device - what should I check?
- Verify the GAIN dip switch position matches the connected source's output level: +18dBu for professional balanced outputs, 0dBu for standard line-level sources, or -10dBv for consumer-level sources.
- The unit has no power and is not connected to a PoE switch - what should I check?
- Connect a regulated 12V DC power supply to the 2-pin Phoenix DC IN connector using the included 2-pin Phoenix male connector as an alternative to PoE.