2x2 XLR and Dante Wall Plate, 2-Gang US, PoE
AUD-DTE-WPXLR 2x2 XLR Dante® wall plate: two mic/line inputs with 48V phantom, two line outputs, AES67, up to 96kHz, PoE Class 1, US 2-gang Decora design.
Puts two mic or line inputs and two line outputs on the Dante network at any wall position, in a US 2-gang Decora plate on one PoE cable. Each XLR input has its own switched 48V phantom power and five-step sensitivity, each output has five-step gain, and the plate takes local 12VDC where the switch has no PoE. Pair it with KanexPro Dante amplifiers and wall plates, and plan it in the KanexPro System Planner with the rest of the room (one drawing and parts list). Puts two mic or line inputs and two line outputs on the Dante® network at any wall position, over a single PoE cable. The AUD-DTE-WPXLR is a 2x2 analog XLR to Dante® converter that fits a standard US 2-gang Decora wall box. It draws 3.6W maximum as an IEEE 802.3af Class 1 powered device, and takes local 12VDC power where the switch has no PoE. Each XLR-F input accepts a balanced or unbalanced microphone or line source and has its own switched 48V phantom power. Each XLR-M output drives an amplifier, powered speaker or recorder at up to 18dBu. It is the right choice for lecture halls, worship stages, council chambers and divisible rooms, where a finished wall connection, phantom control at the plate and a single network drop matter more than a rack-mounted I/O box. Built on the Dante® Ultimo 2x2 platform, the plate carries 2-channel PCM audio at 44.1, 48, 88.2 or 96kHz. It supports AES67 RTP transport for mixed Dante® and AES67 systems, and its device latency is configurable to 1, 2 or 5ms in Dante® Controller, where i
- Two analog inputs and two analog outputs: 2 channels to Dante® and 2 channels from Dante®
- 48V microphone phantom power on each input, switched by a hard button with a backlit LED
- Inputs accept line level up to 24dBu or mic level up to 50mVRMS
- Five-step input sensitivity and five-step output gain controls to match microphones and line-level XLR devices
- Standard US 2-gang Decora design
- PoE (IEEE 802.3af Class 1) or local 12VDC power through a 2-pin Phoenix connector; 3.6W maximum
- Balanced or unbalanced XLR analog audio: 3-pin XLR female inputs and 3-pin XLR male outputs
- Supports AES67 RTP audio transport
- Dante® audio sampling rates of 44.1, 48, 88.2 and 96kHz at 24-bit
- 328ft (100m) to the network switch over CAT6, CAT6A or CAT7
Specifications| Dante® Platform | Dante® Ultimo 2x2 |
|---|
| Control Method | Dante® Controller |
|---|
| Network Bandwidth | 100M |
|---|
| Audio Transport | Dante®, AES67 RTP |
|---|
| Dante® Audio Format | Digital audio in/out, PCM 2-channel, 44.1kHz to 96kHz, 16/24-bit |
|---|
| Sampling Rates | 44.1, 48, 88.2 and 96kHz |
|---|
| Audio Latency | Configurable Dante® device latency of 1, 2 or 5ms, set in Dante® Controller |
|---|
| Transmission Distance | 328ft (100m) over CAT6/6A/7 |
|---|
| ESD Protection | IEC 61000-4-2: ±8kV (air-gap discharge), ±4kV (contact discharge) |
|---|
| Line In | Balanced/unbalanced, maximum input level 24dBu |
|---|
| Mic In | Balanced/unbalanced, maximum input level 50mVRMS, 48V phantom power |
|---|
| Line Out | Balanced/unbalanced, maximum output level 18dBu |
|---|
| Input Sensitivity Control | Five-step, per input |
|---|
| Output Gain Control | Five-step, per output |
|---|
| Output Level (Maximum) | 18dBu |
|---|
| Frequency Response | 20Hz to 20kHz (±0.5dB) |
|---|
| S/N Ratio | > 90dB at 0dBu, 1kHz, A-weighted |
|---|
| Dynamic Range | > 90dB at 0dBu, 1kHz, A-weighted |
|---|
| THD+N | < 0.015% at +4dBu, 1kHz |
|---|
| Output Impedance | 300 Ohm |
|---|
| Audio In | 2x 3-pin XLR female, mic/line |
|---|
| Audio Out | 2x 3-pin XLR male, line |
|---|
| XLR Pinout | Pin 1: Ground/Shield; Pin 2: Positive/Hot; Pin 3: Negative/Cold |
|---|
| Phantom Power Buttons | 2x 48V button with backlit LED (green) |
|---|
| Indicators | 1x Power LED (green), 1x ID LED (green), 2x 48V phantom power LED (green) |
|---|
| Dante® | 1x RJ45 with PoE; LINK LED (yellow), DATA LED (green) |
|---|
| DC In | 1x 2-pin 3.5mm Phoenix connector, 12VDC/500mA |
|---|
| Power Supply | PoE PD (IEEE 802.3af, Class 1), or 12VDC for switches that do not support PoE |
|---|
| DC Input | 12VDC/500mA, 2-pin 3.5mm Phoenix connector |
|---|
| Power Consumption | 3.6W (maximum) |
|---|
Questions
- What are the audio performance figures?
- Frequency response is 20Hz to 20kHz (+/-0.5dB). S/N ratio and dynamic range are both greater than 90dB at 0dBu, 1kHz, A-weighted, and THD+N is under 0.015% at +4dBu, 1kHz.
- What are the maximum input and output levels?
- The line input takes up to 24dBu and the mic input takes up to 50mVRMS, both balanced or unbalanced. The line outputs deliver up to 18dBu, balanced or unbalanced, with a 300 Ohm output impedance.
- How do I find a particular wall plate in Dante Controller?
- Use the identify function in Dante Controller. The green ID LED on the front of that plate lights up so you can see which one it is.
- How is the wall plate configured and controlled?
- It is set up in Dante Controller. That is where you route its channels and set the device latency to 1, 2 or 5ms.
- How are the XLR connectors wired?
- The two inputs are 3-pin female XLR and the two outputs are 3-pin male XLR. Both are wired Pin 1 Ground/Shield, Pin 2 Positive/Hot, Pin 3 Negative/Cold.
- How big is it, and is surge protection recommended?
- The wall plate body measures 3.74 x 4.13 x 1.62 in (95 x 105 x 41.2 mm), and the faceplate is 4.53 x 4.53 x 0.24 in (115 x 115 x 6 mm). A surge protection system is strongly recommended, because spikes, surges and lightning strikes can damage the electronics.
- A condenser microphone gives no signal. What should I check?
- Press the 48V button for that input and confirm its green 48V LED and the button backlight are both on. Then set that input's knob to match the mic level, and confirm the input is routed in Dante Controller.
- Audio is distorted or too quiet. What should I adjust?
- Set each input knob to match the level of the connected source, and each output knob to match the input of the connected equipment. Keep the sources within limits: 24dBu maximum for line and 50mVRMS for mic.
- Can I control it from RelayAV?
- RelayAV shows it on the site so you can see it is there, but it does not control or route it. Set its name, channels and routes in Dante Controller.
- Can it power condenser microphones?
- Yes. Each input has its own 48V phantom power button with a backlit indicator, so phantom power can be switched on or off and checked at the wall without opening any software.