Flex Matrix Pro 128×128 4K60 Crosspoint Modular Matrix Switcher
KanexPro FLEX-PRO128X128 enterprise 128x128 crosspoint matrix routes HDMI, DisplayPort, HDBaseT, fiber optic, and 12G-SDI at 4K60 with native Dante/AES67…
Stadiums. Broadcast centers. Convention halls. Government command posts. When the I/O count exceeds what any single competitor chassis can deliver, the FLEX-PRO128X128 handles it in one frame. Thirty-two input and thirty-two output card slots provide 128 fully routable crosspoints across HDMI, DisplayPort, HDBaseT, fiber optic, and 12G-SDI — all at 4K60 4:4:4, 18Gbps, with seamless switching. Dante/AES67 is native. Power is redundant. Every card is hot-swappable. Every CAT endpoint is PoC-powered. TAA compliant for federal procurement.
- Up to 128 inputs and 128 outputs via hot-swappable 4-port modular cards across five signal formats
- Multi-format I/O: HDMI 2.0, DisplayPort, CAT/HDBaseT 3.0 (330ft), Fiber Optic (2km singlemode), and 12G-SDI
- 4K/UHD 60Hz 4:4:4 at 18Gbps with HDCP 2.2, HDR, and seamless switching on every crosspoint
- Native Dante/AES67 audio networking via built-in MCU card
- Redundant hot-swappable power supplies for mission-critical reliability
- PoC (Power over CAT) delivers power to connected transmitters and receivers from the main chassis
- Video wall, quad view, independent output scaling, CEC display control, and EDID/HDCP management
- TAA compliant for U.S. government procurement
Specifications| Standard | HDMI 2.0, HDCP 2.2 |
|---|
| HDR | Supported |
|---|
| Max Data Rate | 18 Gbps (HDMI/DP) / 11.88 Gbps (12G-SDI) |
|---|
| Max Resolution | 4096×2160 @60Hz 4:4:4 |
|---|
| Switching | Seamless (glitch-free crosspoint) |
|---|
| Network Audio | Dante/AES67 (built-in via FLEX-MCU-Dante) |
|---|
| Pass-through | LPCM 8ch, Dolby TrueHD, DD+, DTS-HD MA, DTS:X |
|---|
| Input Slots | 32 slots × 4 ports = 128 inputs max |
|---|
| Output Slots | 32 slots × 4 ports = 128 outputs max |
|---|
| Card Types | HDMI, DisplayPort, CAT (HDBaseT 3.0), Fiber Optic, 12G-SDI |
|---|
| CAT | 330ft (100m) via CAT6A, PoC supported |
|---|
| Fiber | Multimode 984ft (300m) / Singlemode 6,562ft (2km) |
|---|
| 12G-SDI | Per SMPTE standards |
|---|
| Interfaces | 7" Touch, TCP/IP, Web GUI, RS-232, Dante Controller |
|---|
| Power | Redundant hot-swappable PSUs, 100–240VAC |
|---|
| Compliance | TAA Compliant |
|---|
Questions
- Is KanexPro reliable for mission-critical deployments?
- Redundant hot-swappable PSU, hot-swappable I/O cards, automatic cable compensation, signal reclocking ensure 24/7 uptime. TAA compliant for government.
- Does it support videowall and multiview?
- Built-in videowall processing and quad view on all outputs with independent scaling. No external videowall processor needed.
- Can I start small and scale up?
- Same card architecture works across 16x16, 32x32, 64x64, 128x128 chassis. Cards are interchangeable.
- How to install I/O cards?
- Hot-swappable. Slide in until click. Press release latch to remove. No shutdown needed.
- Rack space required?
- 39 RU in standard 19-inch rack. 483 x 368 x 1700 mm.
- No video on output?
- Verify I/O card is fully seated. Check source via touch panel. For CAT/Fiber, verify endpoint receiver. Try different EDID mode.
- Dante audio not routing?
- Confirm FLEX-MCU-Dante board installed and Dante port on same network. Use Dante Controller to verify discovery.
- What about total cost of ownership?
- Built-in Dante eliminates separate audio matrix/DSP. PoC eliminates per-endpoint power supplies. Five signal types on one frame.
- TAA compliant?
- Yes. Qualified for U.S. government procurement.
- What fiber types are supported?
- Multimode 984ft/300m and singlemode 6,562ft/2km via LC fiber connectors.