Flex Matrix Pro 16×16 4K60 Crosspoint Modular Matrix Switcher
KanexPro FLEX-PRO16X16 crosspoint matrix routes HDMI, DisplayPort, HDBaseT, fiber, and 12G-SDI at 4K60 18Gbps with Dante/AES67 in a scalable 16x16 chassis.
Five signal formats. One crosspoint chassis. Zero external converters. The FLEX-PRO16X16 accepts HDMI 2.0, DisplayPort, HDBaseT 3.0 (330ft/100m), fiber optic (2km singlemode), and 12G-SDI inputs on hot-swappable 4-port cards — routing any source to any of 16 outputs at 4K/UHD 60Hz 4:4:4, 18Gbps, with HDCP 2.2 and seamless switching across every crosspoint. Dante/AES67 audio built into the MCU card. Redundant hot-swappable PSUs. PoC for CAT endpoints. Independent output scaling. Video wall and quad view. RS-232, TCP/IP, Web GUI, 7" touchscreen. TAA compliant. Expandable: same card ecosystem scales to 32×32, 64×64, and 128×128 Pro chassis.
- 16×16 crosspoint: 4 input + 4 output card slots × 4 ports each — HDMI, DisplayPort, CAT, Fiber, or 12G-SDI in any combination
- 4K/UHD 60Hz 4:4:4 • 18Gbps • HDCP 2.2 • HDR • seamless switching • independent output scaling
- Dante/AES67 native via FLEX-MCU-Dante — 8ch LPCM, Dolby TrueHD, DTS-HD MA passthrough
- HDBaseT 3.0: 330ft/100m uncompressed 4K60 over CAT6A with PoC • Fiber: 984ft MM / 6,562ft SM
- 12G-SDI: 12G/6G/3G/HD-SDI at up to 11.88Gbps • SMPTE/ITU compliant • auto reclocking
- Redundant hot-swappable PSUs • bi-directional RS-232 and LAN to endpoints
- Video wall (up to 4×3) • quad view • CEC display control • EDID/HDCP management • preset save/recall
- TAA compliant • 7" touch panel • Web GUI • Dante Controller • Dante Domain Manager ready
Specifications| Crosspoint | 16×16 (4+4 slots × 4 ports) |
|---|
| I/O Formats | HDMI 2.0, DP, CAT (HDBaseT 3.0), Fiber, 12G-SDI |
|---|
| Resolution | 4096×2160 @60Hz 4:4:4, 18Gbps, HDCP 2.2, HDR |
|---|
| Audio | Dante/AES67, LPCM 8ch, Dolby TrueHD, DTS-HD MA |
|---|
| CAT | 330ft (100m), PoC |
|---|
| Fiber | MM 984ft / SM 6,562ft |
|---|
| SDI | 12G/6G/3G/HD-SDI, 11.88Gbps |
|---|
| Power | Redundant hot-swappable PSUs |
|---|
| Compliance | TAA |
|---|
Questions
- What is the maximum I/O capacity of the FLEX-PRO16X16 chassis?
- The FLEX-PRO16X16 is a fully modular 16x16 crosspoint matrix with 4 input card slots and 4 output card slots, each accepting a 4-port card, for up to 16 inputs and 16 outputs total.
- What video performance does the FLEX-PRO16X16 support?
- The chassis routes 4K/UHD signals at up to 4096x2160 @60Hz 4:4:4 with an 18Gbps data rate, HDCP 2.2 compliance, HDR support, and seamless glitch-free crosspoint switching.
- How is the FLEX-PRO16X16 controlled?
- Control is available through the 7-inch front panel capacitive touchscreen, TCP/IP (RJ45) with Web GUI, bi-directional RS-232 to endpoints, Dante Controller software, and Dante Domain Manager.
- Can the FLEX-PRO16X16 drive a video wall?
- Yes. The chassis supports video wall layouts up to 4x3, quad view multi-viewing, independent output scaling, CEC display control, and EDID/HDCP management, with preset save and recall.
- Are the I/O cards hot-swappable?
- Yes, all input and output cards, the FLEX-MCU-Dante card, and both power supplies are hot-swappable, allowing service without powering down the chassis.
- How are remote CAT endpoints powered?
- PoC (Power over CAT) delivers power to FLEX-PROCAT-TX and FLEX-PROCAT-RX endpoints directly from the chassis, eliminating the need for local power adapters at each endpoint.
- No video on one or more outputs, what should I check?
- Verify the output card is fully seated and its LED shows normal operation, confirm the source is active on the corresponding input card, and for CAT/Fiber outputs confirm the receiver is powered (or PoC is enabled) and connected. Try matching EDID to the display's native resolution.
- Dante audio is not routing between devices, what is the fix?
- Confirm the FLEX-MCU-Dante card is installed and its LAN port is connected to the Dante network, open Dante Controller to verify the device is visible, and check that audio routes are configured in Dante Controller.
- Why choose the FLEX-PRO16X16 for government or institutional procurement?
- The FLEX-PRO16X16 is TAA compliant, making it eligible for U.S. government procurement while providing an enterprise-grade 16x16 crosspoint platform with redundant power and native Dante/AES67 audio.
- What advantage does a 5-format crosspoint offer over single-format matrices?
- Consolidating HDMI, DisplayPort, HDBaseT, fiber, and 12G-SDI routing into one chassis eliminates the need for separate matrix infrastructure per signal type, simplifying large-venue AV designs that must support mixed source and display formats.