4K60 HDMI-to-Fiber Transmitter for Flex Matrix Pro
KanexPro FLEX-PROFIB-TX for Flex Matrix Pro. HDMI In / Fiber Out. 4K60, Dante/AES67, TAA.
Place an HDMI source up to 2km from the chassis via fiber optic. The FLEX-PROFIB-TX converts HDMI to fiber (adaptive SM/MM) with RS-232. Connects to FLEX-PROFIB-IN. 4K60 4:4:4, 18Gbps, HDCP 2.2. EDID/HDCP management. Seamless switching. TAA compliant.
- 4K60 4:4:4 at 18Gbps • HDCP 2.2 • HDR
- Singlemode 2km • Multimode 300m • adaptive processing
- Bi-directional RS-232 for endpoint control
- EDID/HDCP management • seamless switching
- TAA compliant
Specifications| Input port | 1 X HDMI 2.0 |
|---|
| Output Port | 1 X LC Fiber Port |
|---|
| Compliance | HDCP 2.2, EDID Management |
|---|
| Video Resolution: | Up to 3840x2160 60Hz 4:4:4 (8bit) |
|---|
| Operating Distance: | Single-mode 1.24 Mile (2 KM), Multi-mode 984 mile (300 m) |
|---|
| Normal Peak Wavelength | 1550nm, 1310nm |
|---|
| Analog Audio Port | 1 X 3-pin Phoenix stereo audio for Extraction |
|---|
| Control Port | 1 X 3 Pin Phoenix (RS232) |
|---|
| Power Supply | 12V DC, 1 X 3 pin Phoenix Connector |
|---|
| Compliant | TAA |
|---|
Questions
- What is the maximum resolution supported by the FLEX-PROFIB-TX?
- Up to 3840x2160 @60Hz 4:4:4 (8-bit), with HDCP 2.2 compliance and EDID management.
- What are the FLEX-PROFIB-TX's video connectors?
- 1x HDMI 2.0 input port and 1x LC fiber output port.
- How is the FLEX-PROFIB-TX controlled by a third-party system?
- It provides bi-directional RS-232 via a 3-pin Phoenix connector for endpoint control.
- Which chassis card does the FLEX-PROFIB-TX connect to?
- It connects directly to the Flex Pro Fiber Optic input card (FLEX-PROFIB-IN).
- What is the maximum fiber run for the FLEX-PROFIB-TX?
- It is compatible with both multimode fiber, up to 984ft (300m), and singlemode fiber, up to 6,562ft (2km), transmitting video, audio, and bidirectional RS-232 over a single fiber cable.
- How is the FLEX-PROFIB-TX powered?
- It is powered by 12V DC through a 3-pin Phoenix power connector.
- No video appears at the far end of the fiber link, what should I check?
- Confirm the fiber run does not exceed 300m (984ft) for multimode or 2km (6,562ft) for singlemode, verify the unit has 12V DC power connected via the Phoenix connector, and confirm the HDMI source is active.
- HDCP-protected content will not display, what should I check?
- Confirm HDCP 2.2 support on the source and connected chassis/receiver, and verify EDID management is set to match the display's capabilities.
- What advantage does fiber transmission offer over CAT extension for this application?
- The FLEX-PROFIB-TX reaches up to 6,562ft (2km) over singlemode fiber, far beyond the 330ft (100m) limit of CAT6A extension, making it suited for inter-building or long-distance 4K distribution.
- Is the FLEX-PROFIB-TX suitable for government-spec projects?
- Yes, it is TAA compliant.