KanexPro Support Assistant

Describe your setup, the part number, and what you are seeing.

Before we start

So the team can follow up if this needs a person.

Used only to follow up on this request. See our Privacy Policy.

General enquiry

Tell us what you need and the right person will come back to you.

Used only to answer you. See our Privacy Policy.

Support › Knowledge base › CBL-AOCHDMI8K-60M

HDMI 2.1 Active Optical Cable: What It Is and Does

CBL-AOCHDMI8K-60M CBL-AOCHDMI8K-60M 8K HDMI 2.1 Active Optical Cable - 60M (197 ft.) 48Gbps | 8K@60Hz | 4K@120Hz | eARC | Dynamic HDR | 3-Year Warranty Product page →

This is an HDMI 2.1 active optical cable (AOC) for runs that are too long for passive copper HDMI cable, such as a source in an equipment rack feeding a display far away. It is for integrators who need one cable from source to display, with no wall adapters, repeaters or signal processors along the run. It is plug and play: there are no drivers and nothing to configure.

Applies to: CBL-AOCHDMI8K-60M, HDMI 2.1 active optical cable.

What is an active optical HDMI cable, and what is inside this one?

An active optical cable converts the HDMI signal to light at one end and back to electrical at the other. This cable uses a 4-channel 850nm VCSEL array to drive an OM3 fiber + copper hybrid cable. The jacket is 4.5mm OD and black, so the cable is slim enough for wall and conduit runs. Because the signal travels over fiber, the cable is immune to EMI/RFI.

What bandwidth and resolutions does it carry?

The cable is built to the HDMI 2.1 standard at 48Gbps, made up of 12Gbps x 4 channels. It supports 8K @ 60Hz, 4K @ 120Hz and 4K @ 144Hz. It is HDCP 2.2 compliant, supports the full EDID handshake and is backward compatible with HDMI 2.0 and 1.4 equipment.

What do the source and display need for 8K@60Hz?

To get 8K@60Hz, both the source and the display must be HDMI 2.1 devices, because that mode needs the full 48Gbps link at both ends. When either end is an HDMI 2.0 or 1.4 device, the cable still works through its backward compatibility.

Which HDR formats pass through it?

The cable passes Dynamic HDR in four formats: HDR10, HDR10+, Dolby Vision and HLG. It does not process the HDR metadata. It carries the metadata from the source to the display.

Does it support eARC?

Yes, eARC (Enhanced Audio Return Channel) is fully supported. eARC sends Dolby Atmos and DTS:X audio back to an AV receiver or soundbar, so a display can return its audio to the sound system over the same cable.

Does it need a power supply?

No. The cable is bus-powered from the HDMI source and draws 250mW max. You do not need an external supply at either end, and you do not need an outlet near the display for the cable.

Why are the two ends labeled SOURCE and DISPLAY?

The cable is directional. The connector labeled SOURCE goes to the source, and the connector labeled DISPLAY goes to the display. If you fit it the other way round, it passes no picture. Both ends are HDMI Type A Male. Check the labels before you pull the cable through conduit so the correct end arrives at the rack.

How long is this version, and are other lengths available?

This version is 60 meters (197 ft.) long. The same cable is also made in 30M and 90M lengths, so you can order the length that suits the pull. It is rated for 0 to +50 degrees C and comes with KanexPro's 3-year warranty.

Key specifications

StandardHDMI 2.1 (48Gbps) · HDCP 2.2 · Backward compatible HDMI 2.0 / 1.4
Video Bandwidth12Gbps x 4 channels = 48Gbps total
Max Resolution8K @ 60Hz · 4K @ 120Hz · 4K @ 144Hz
HDR SupportHDR10 · HDR10+ · Dolby Vision · HLG
eARCEnhanced Audio Return Channel — full support
ConnectorHDMI Type A Male (both ends, directional)
OE Converter4-channel 850nm VCSEL array
Cable TypeOM3 fiber + copper hybrid · 4.5mm OD · Black
Power SupplyBus-powered from HDMI source — no external supply required
Power Consumption250mW max
Operating Temperature0 to +50 degrees C